Edgers, resaws and debarkers explained

A sawmill line is a set of machine centers, each with one job. The debarker cleans the log, the headrig opens it into cants and boards, the edger squares board edges, the resaw or multirip splits cants into more boards, and the trimmer cuts them to length. Conveyors move wood between them.

A Wravor WRC 1550 band headrig on its line with red log decks in a new mill hall

By Bailey's sawmill team · Updated · 4 min read

Follow the log

  1. 1Log deck
  2. 2DebarkerOut: Bark
  3. 3HeadrigOut: Slabs, sawdust
  4. 4EdgerOut: Edgings
  5. 5Resaw / MultiripOut: Sawdust
  6. 6Trimmer
  7. 7Sorting and stacking

The order below is the order a log meets them. Small mills combine steps or do some by hand; large mills add machines at each step.

Log debarker

A debarker strips bark from the log before it reaches the headrig. Bark carries grit, sand and small stones, and those dull saw blades fast; taking bark off first keeps blades sharp longer and keeps bark out of the sawdust and chips. Debarkers are sized by the log diameters they take. Wravor, for example, publishes a range of 200 to 1500 mm for its debarkers.

Headrig

The headrig is the first saw in the mill. It takes the whole log and opens it, sawing off slabs and cutting cants (squared timbers) and boards. On the industrial side the headrig is usually a horizontal band saw: the log is held on a carriage or bed and the band head cuts it pass by pass. Because every log goes through it, the headrig sets the pace of the mill.

Edger

Boards off the headrig often still have bark or wane along their edges. The edger saws those edges straight and parallel, so each board leaves at the widest clean width the log allows. Edgers range from manual board edgers, where the operator sets the cut, to automated edgers that scan each board and choose the width. A multirip edger takes several widths from one board in one pass.

Resaw

A resaw splits a cant or thick flitch into thinner boards. Its job is to take work off the headrig: the headrig makes a few quick cuts, the cant goes to the resaw, and the headrig moves on to the next log. Horizontal resaws lay the cant flat and saw boards off it; some lines return the cant in a loop until it is fully sawn.

Multirip

A multirip, or gang saw, rips a cant into several boards in one pass, with blades set at the board thickness. Multirips suit mills cutting the same sizes over and over, such as pallet stock.

Trimmer

The trimmer cuts boards to length and squares their ends, taking out defects at the end of a board. In smaller mills this is a crosscut saw; larger lines use multi-saw trimmers.

Handling between machines

Decks, conveyors, roll cases, transfer tables and sorting tables move logs and lumber between machine centers. Handling decides how smoothly the line runs: a fast headrig waiting on a slow conveyor isn’t fast. When a mill grows, handling is often the first thing to add.

The makers Bailey’s carries

Bailey’s quotes two industrial makers’ machine centers:

  • Wood-Mizer industrial systems: headrigs, edgers (from the EG800 Board Edger to the EA1000 and EA3000 Automated Edgers), HR horizontal resaws, MR multirips, and log decks and conveyors. See Wood-Mizer, edgers and resaws and log decks and conveyors.
  • Wravor: WRC horizontal bandsaws, edgers, debarkers and complete sawing lines. See Wravor.

For headrigs and complete lines from both, see industrial sawmills.

Questions sawyers ask

Anything else, call a specialist at 1-888-465-8227.

What is a resaw in a sawmill?

A resaw is a machine that splits a cant or thick flitch into thinner boards. It takes work off the headrig, which can then make a few quick cuts and move on to the next log.

What does a log debarker do?

A log debarker strips the bark from a log before it is sawn. Bark carries grit and stones that dull saw blades, so debarking first keeps blades sharp longer and keeps bark out of the sawdust and chips.

What is an edger in a sawmill?

An edger saws the bark and wane off the edges of a board so its edges are straight and parallel. Manual edgers are set by the operator; automated edgers scan each board and choose the width.

What is a headrig?

A headrig is the first saw in a sawmill. It takes the whole log and opens it into slabs, cants and boards for the machines downstream. Industrial headrigs are usually horizontal band saws.

What is the difference between a resaw and a multirip?

A resaw saws boards off a cant, usually one or a few at a time, often looping the cant back until it is sawn through. A multirip, or gang saw, cuts a cant into several boards in one pass.

Does every sawmill need all of these machines?

No. A small mill may run a headrig with manual edging and trimming. Machine centers are added as production grows. A specialist can help you plan which to buy first.

Plan your mill with a specialist

Tell us about your logs, the output you want and the site. The more we know, the closer the first quotation is to the mill you need.

Fields marked optional can be skipped. Everything else helps the specialist quote the right setup.

More about your job (optional)

Interested in financing?
Best way to reach you

We use your details to answer this request. See Bailey's privacy policy and terms.